8 800 301-97-66
geosoftdent@geosoft.ru
Development, production, sale, promotion of dental equipment and technologies

System «Estus Pack-Fill» for the tooth root canals 3D obturation by the heated gutta-percha on the obturation steps: “DownРack” and “BackFill”. “Estus Pack-Fill” consists of two functional handpieces: 1. “Estus Pack” is for heating, vertical condensation of the dental gutta-percha and cutting the gutta-percha tips in the root canal on the obturation step “DownPack” and thermal activation of the irrigating solutions. 2. “Estus Fill” is for the heating and the following injection of the heated gutta-percha into the root canal by the special injector needle on the step of obturation “BackFill”.

 

Select Delivery set
Download files

Advantages

1. DOWNPACK-HANDPIECE «ESTUS PACK»:

  • DownPack-handpiece ESTUS PACK of a new generation provides:
    – high quality vertical condensation,
    – cutting of gutta-percha points,
    – heat endoactivation of irrigational solution
  • Safe thermoplugger with integrated sensor feedback allows:
    – to ensure high accuracy of maintaining the set working temperature,
    – to decrease the working temperature in a root canal down to 100°С, which causes:
    – reducing of thermoplugger heating time down to the set working temperature (not > 1,5 sec),
    – prevention of gutta-percha over-heating that worsens its characteristics,
    – prolongation of save canal treatment without risk of periodontal tissues over-heating,
    – prolongation of thermopluggers service life
  • There are 3 types quick-detachable and autoclavable thermopluggers for different stages of root canal obturation:
    – obturation of the apical zone,
    – obturation of the upper 2/3 canal,
    – cutting of gutta-percha points
  • Possibility to fix the thermoplugger in 1 of the 6 available positions
  • Effective condensation of gutta-percha thanks to vibration function

 

  • ESTUS PACK can perform either as autonomous device or as a part of ESTUS dental complex, the main part of witch is ESTUS MULTI control unit (sold separately)

2. BACKFILL-HANDPIECE «ESTUS FILL»:

  • BackFill-handpiece ESTUS FILL – the only syringe type injector is able to work with cost effective gutta-percha obturators
  • Easy detachable autoclavable heater
  • Time to prepare device ready for operation doesn’t exceed 20 sec (heating an injector needle and softening gutta-percha)
  • 2 modes of heated gutta-percha delivery:
    – PORTION mode for the one-stage of an apical plug creation,
    – CONTINUOUS mode for filling of middle and upper parts of the root canal
  • 3 feed rates of heated gutta-percha
  • Safe performance – the heater corpus temperature doesn’t exceed 45°С
  • High-quality consumables: gutta-percha obturators and two size types of Injector needles (№23G and №25G)
  • Fully charged battery is enough for injection of 50 pcs of gutta-percha obturators
  • Maximal comfort in operation is provided by a single button – Ring Switch. Convenient both for left – and right-handers
  • Prevention of accidental switch on due to restriction of working zone (upper 180°) of Ring Switch
  • Excellent ergonomic characteristics of handpiece:
    -specifically designed, provides a super balanced position in the dentist’s hand,
    -low weight and excellent visibility of indicators location is in the direct closeness to the working zone
  • 1600 mAh easily replaceable battery units always keep the handpiece in operating condition

 

  • ESTUS FILL can perform either as autonomous device or as a part of ESTUS dental complex, the main part of witch is ESTUS MULTI control unit (sold separately)

_________________________________

  • Maximal comfort in operation is provided by a single button – Ring Switch. Convenient both for left – and right-handers
  • Prevention of accidental switch on due to restriction of working zone (upper 180°) of Ring Switch
  • Excellent ergonomic characteristics of handpiece:
    -specifically designed, provides a super balanced position in the dentist’s hand,
    -low weight and excellent visibility of indicators location is in the direct closeness to the working zone
  • 1600 mAh easily replaceable battery units always keep the handpiece in operating condition

Delivery sets

Set "Estus Pack-Fill" GЕ40E-P-F
1 029 $
Buy

Complete set PLUS, with charger and stand  – a full set of the device

The set consists of

  • – Control unit «Estus Pack»
  • – Control unit «Estus Fill»
  • – 2 Battery unit (8V)
  • – Thermoplugger «S» (02/45)
  • – Thermoplugger «M» (04/50)
  • – Thermoplugger «L» (08/55)
  • – Нeater «Estus Fill»
  • – 2 Injector needles (23G and 25G)
  • – Gutta-percha obturators (10 pcs.)
  • – Cleaning and level measuring tool gutta-percha in a heater
  • – Multi-functional wrench for injector needle
  • – Stand “Estus Two -B” (double)
  • – Сharging stand “Estus Energy-D” (double)
  • – Charger cable USB – USB-B
  • – Power adapter (2A)

Specifications

  • Estus Pack / Estus Fill  handpieces power supply: Li-Ro battery unit (2×3.7V; 800mAh) with charging from the charging stand

for “Estus Pack” handpiece:

  • Operating temperature  in the mode: 1. of the gutta-percha cutting  “CUT” – 150 ±10°С, 2. of the gutta-percha condensing “PACK” – 100 ±10°С, 3. of the thermal activation of irrigant “MIX” – 50 ±5°С
  • Adjustment of the operating temperature  in the “PACK” mode when working Estus Pack with the ESTUS MULTI control unit: from 80 to 120°С (step 10°С)
  • Stabilization accuracy of the working temperature – ±2°С
  • Thermoplugger heating time to the set operating temperature: not more than 1.6 sec.
  • Maximal duration of the thermoplugger heating cycle with the following automatic switch off in the mode: 1. of the gutta-percha cutting “CUT” – 7 sec., 2. of the gutta-percha condensing “PACK” – 12 sec., 3. of the thermal activation of irrigant “MIX” – 120 sec.
  • Performance duration with the new fully charged battery unit – is not less than 500 heating cycles.

for “Estus Fill” handpiece:

  • The temperature of the gutta-percha injection (operating temperature): – 180±5°С
  • Adjustment of the operating temperature when working Estus Fill with the ESTUS MULTI control unit: from 160 to 200°С (step 10°С)
  • Stabilization accuracy of the operating temperature- ±10°С
  • The time of heating from 20°С to 180°С – 15 ± 5 sec
  • The time of extrusion of the one standard gutta-percha obturator:  for the “High”  feed rate – 30 sec, for the “Middle” feed rate – 65 sec, for the “Low” feed rate – 140 sec
  • Working temperature keeping in stand-by mode – 3,0 ± 0,1 min.
  • Performance duration with the new fully charged battery unit without boost charge – 13-15 heating cycles 3 min. each.
  • The heater external surface temperature – is not more than 45°С
  • The injector needle tip temperature – is not more than 75°С

__________________

  • Stand-by operating time to automatic switch off : 10 ±0,5 minutes
  • Max. battery unit charging time: 3 h
  • “Estus Pack” dimensions/ weight: (207*33*43) ±3 mm/ 80 ±10 g
  • “Estus Fill” dimensions /weight: (240*33*43) ±3 mm / 115 ±10 g
  • The built-in radio module NF-03: frequency range – 2,4-2,525 GHz, max output capacity – 7 dBm, cover range -up to 3 m in the direct vision.
  • «Estus Energy-D» charging stand dimensions / weight: (87*56*49) ±3 mm / 145±10 g
  • Power adapter parameters: Input voltage (100-240) V, ~50/60Hz, Output voltage 5V; 2A
  • «Estus Two-B» stand dimensions / weight: (102*100*40) ±3 mm / 155±10 g

Accessories

Thermoplugger “S”. GE99.142.000
Thermoplugger “S”. GE99.142.000

Thermoplugger for heating and condensing gutta-percha in the apical area (one-third) of the canal. Size 02/ 45  

Thermoplugger “М”. GE99.144.000
Thermoplugger “М”. GE99.144.000

Thermoplugger for heating and condensing gutta-percha in the two-thirds of the canal. Size  04/ 50  

Thermoplugger “L”. GE99.146.000
Thermoplugger “L”. GE99.146.000

Thermoplugger for the gutta-percha tips cutting. Size  08/ 55

Heater “ESTUS” GE99.213.000
Heater “ESTUS” GE99.213.000

Optional sterilizable heater for the “Estus Fill” handpiece.

Gutta-percha obturators. GE99.188.000
Gutta-percha obturators. GE99.188.000

Gutta-percha obturators for the “Estus Fill” handpiece. Type: Soft, Medium, Hard

Injector needles (23G). GE99.186.000
Injector needles (23G). GE99.186.000

Injector needles for the “Estus Fill” handpiece (gauge 23G)

Injector needles (25G). GE99.187.000
Injector needles (25G). GE99.187.000

Injector needles for the “Estus Fill” handpiece (gauge 25G)

Tools kit for the “Estus Fill” handpiece. GE99.251.000
Tools kit for the “Estus Fill” handpiece. GE99.251.000

Tools kit for the “Estus Fill” handpiece (2 items).

Spare gaskets for the “Estus Fill” handpiece. GE99.201.000
Spare gaskets for the “Estus Fill” handpiece. GE99.201.000

Spare gaskets for the “Estus Fill” handpiece.

Battery unit (8V) GЕ99.205.000
Battery unit (8V) GЕ99.205.000

Battery unit (8V) with charging from the Estus Energy-S / Estus Energy-D charging stand for all ESTUS handpieces and the ESTUS PUMP irrigation pump.

Charging stand «Estus Energy-S» GЕ42.000.000
Charging stand «Estus Energy-S» GЕ42.000.000

One-port charging stand for the battery unit (8V) of the “Estus” devices.  

Charging stand «Estus Energy-D» GЕ39.000.000
Charging stand «Estus Energy-D» GЕ39.000.000

Two-ports charging stand for two battery units (8V) of the “Estus” devices.  

Charger cable USB-USВB. GЕ99.001.00P
Charger cable USB-USВB. GЕ99.001.00P

Cable for charging stand «Estus Energy-S» / «Estus Energy-D» and «Estus Multi», «EndoEst-Apex 02 (С)», «EndoEst-3D», «EndoEst» devices.

Power adapter (USB-socket) 2А. GЕ99.006.00P
Power adapter (USB-socket) 2А. GЕ99.006.00P

Power adapter 2А

Stand «Estus One-B» GЕ99.208.000
Stand «Estus One-B» GЕ99.208.000

Single-stand for the all “Estus” handpieces.  

Stand «Estus Two-B» GЕ99.209.000
Stand «Estus Two-B» GЕ99.209.000

Double-stand for all “Estus” handpieces  

Photo and Video

Guarantees

1.The manufacturer guarantees the device correct operation according to the technical specification requirements, technical conditions 9452-014-56755207-2016 when the user follows all the regulations, service and storage conditions.

2. Warranty period is 2 years from the purchase date , but not more than 2,5 years since the day of manufacturing (except p.3). Warranty enters into force with the day when the buyer acquires the product from the seller.

3. The battery unit warranty period in the device delivery set is 6 months since the sale date. The thermopluggers, gutta-percha obturators and injector needles in the device delivery set is not covered under warranty.

4. The warranty does not apply if the device has mechanical defects or has not been used in accordance with the User’s manual

5. Warranty repairs are performed at the Manufacturer’s service center or other authorized service center. Delivery of the device to the service center is at the expense of the device owner.

6. The device is accepted for warranty repair only in FULL configuration, including a Quality Warranty card with the manufacturer’s seal and the seller’s marks. If the Quality Warranty Card is filled in incorrectly, this may cause the warranty repair to be refused.

7. The manufacturer reserves the right to make changes and supplements to the device construction not worsening its basic technical specification.

See also

Device for root canal obturation ESTUS PACK
Device for root canal obturation ESTUS PACK

Device “Estus Pack” for heating, vertical condensation of the dental gutta-percha and cutting the gutta-percha tips in the root canal on the obturation step “DownPack” and thermal activation of the irrigating solutions.  

Device for root canal obturation ESTUS FILL
Device for root canal obturation ESTUS FILL

Device «Estus Fill» for the heating and the following injection of the heated gutta-percha into the root canal by the special injector needle on the step of obturation “BackFill”.  

Contact us

    Leave your contact details,
    and we will contact you

    By clicking on the button, you agree to the_Privacy Policy.